EXTREME Floor Protection for EXTREME Environments
Easy to apply ENECLAD FPS seals and protects concrete floors. This extraordinary high-performance polymer composite is extremely abrasion resistant, making it ideal for heavy traffic areas in warehouses, hangars, loading docks, etc. FPS jackets the surface in a rugged, armored coating that resists forklift traffic, oil, gasoline and many common industrial chemicals.
ENECLAD FPS is a solvent-free, virtually odor-free, two-component product specifically developed to solve some of the toughest industrial floor protection problems. It is easily applied by brush, roller or squeegee to a super high-gloss finish. Non-skid aggregates can be incorporated into the ENECLAD FPS to provide a highly durable, slip resistant surface.
ENECLAD FPS high performance polymer system has been specifically formulated for new or old concrete floors. FPS produces a seamless surface that is easy to clean and easy to maintain.
Prior to applying ENECLAD FPS to concrete and / or cementitious substrates, the surface should be treated with CHEMCLAD® P4C to seal the surface, minimize outgassing and insure that optimum adhesion is obtained.
- Traffic Resistance
- Abrasion Resistance
- Chemical Resistance
- Oil Resistance
- Detergent Resistance
- Easy Application
- Easy Maintenance
- No V.O.C’s
- No Odor
Technical Data
- Volume capacity per kg.
- 46 in3 / 750 cc
- Mixed density
- 0.048 lbs per in3 / 1.31 gm per cc
- Coverage rate per kg. @ 12 mils / 300 microns
- 25 ft2 / 2.3 m2
- Shelf life
- Indefinite
- Volume Solids
- 100%
| Mixing ratio | Base | Activator |
|---|---|---|
| By Volume | 2 | 1 |
| By Weight | 3 | 1 |
Colors
Tile Red
Haze Gray
Note: Other colors are available on a “special order” basis. However, there are minimum / multiple quantity requirements for such orders and there may be an increase in cost. Additionally, due to formulation restrictions, not all colors are possible for all materials. Speak to your local ENECON Sales Representative for more information.
Due to monitor / printer differences, actual colors may vary slightly from the representations appearing in this chart.
Cure Times
| Ambient Temperature | Working Life | Touch Dry | Maximum Overcoat | Full Cure | |
|---|---|---|---|---|---|
| 59°F | 15°C | 90 min. | 24 hrs. | 48 hrs. | 6 days |
| 77°F | 25°C | 70 min. | 16 hrs. | 24 hrs. | 4 days |
| 86°F | 30°C | 55 min. | 8 hrs. | 16 hrs. | 3 days |
Physical Properties
| Typical Values | Test Method | ||
|---|---|---|---|
| Compressive strength | 11,000 psi | 770 kg/cm2 | ASTM D-695 |
| Flexural strength | 9,000 psi | 630 kg/cm2 | ASTM D-790 |
| Hardness - Shore D | 86 | ASTM D-2240 | |
| Abrasion resistance | 35 mg / 1,000 cycles | ASTM D-4060 | |
| Shear Adhesion | |||
| Steel | 4100 psi | 287 kg/cm2 | ASTM D-1002 |
|
Elcometer Adhesion - to properly
prepared cementitious surfaces is greater than the cohesive strength of the substrate. |
|||
CHEMCLAD P4C Technical Data
- Theoretical coverage rate per kg. @ 3 mils
- 70 - 80 ft2 / 6 - 7 m2
| Mixing ratio | Base | Activator |
|---|---|---|
| By Volume | 2 | 5 |
| By Weight | 2 | 5 |
| Ambient Temperature | Working Life | Minimum Overcoating | Maximum Overcoating | |
|---|---|---|---|---|
| 41°F | 5°C | 120 min. | 16 hrs. | 48 hrs. |
| 59°F | 15°C | 75 min. | 12 hrs. | 36 hrs. |
| 77°F | 25°C | 60 min. | 8 hrs. | 24 hrs. |
| 86°F | 30°C | 50 min. | 5 hrs. | 16 hrs. |
Chemical Resistance
| Gasoline | EX | Detergent Solution | EX |
| Kerosene | EX | Trisodium Phosphate | EX |
| 50% Anti-Freeze | EX | 20% Calcium Chloride | EX |
| Transmission Fluid | EX | 10% Hydrochloric Acid | EX |
| Power Steering Fluid | EX | 10% Sulfuric Acid | EX |
| Motor Oil | EX | 10% Sodium Hydroxide | EX |
EX - Suitable for most applications including immersion
G - Suitable for intermittent contact, splashes, etc.
